Avenger Cnc Beam

Q Drill Bit

The CNC Beam Drill Line, which can be used to fabricate structural steel or miscellaneous metallics, was immediately a hit with small to medium size fabricators. Since 2003, more than 600 CNC Beam Drill Lines were installed all over the globe. This incredible machine has transformed the lives many a steel fabricator.

The CNC Beam Drill Line is built exclusively for GSS Machinery by Voortman. Voortman handles the installation, warranty and service work on the CNC Beam Drill Line. And while Voortman is the service provider, GSS Machinery is always there to get involved should the need arise.

Cnc Beam Drill Line 50

Voortman will install and calibrate your machine once he is done. Then, he will meet with your operators and take them through the simple but comprehensive training program. They will be trained in:

The CNC Beam Drill Line can not only process columns and beams, but also all steel profiles, including channel, angle and flat bars, base plates, RHS square and round.

Drilling

Drilling

"..In our efforts to satisfy customer demands and increase productivity, we installed a new beam drilling line. This has resulted in a lower labor cost and faster turnaround times that have always helped us land high quality jobs.

CNC Beam Drill Line has a 100% hydraulic motor, which makes maintenance and parts extremely affordable. CNC Drill line was created to be used around the globe and uses components only from major manufacturers. However, many of the parts can be purchased locally. Voortman has all the parts in stock for next-day delivery to the USA. In many of our overseas countries, we offer local support and service.

Q Drill Bit

Cnc Beam Drill Line Configuration

The Advantage-2 carbide drill line utilizes automatic tool changing technology and completely electronic ball screw feed spindle motion. This combined with Voortman' renowned build quality and mechanical design provide the ultimate combination of agility and strength.

Voortman developed Raptor 3DCAD/CAM Software, which takes CNC innovation to the next level by allowing users to program more quickly and accurately. The 3D platform allows you to inspect, modify, and export part information. This, combined with Voortman CNC technology, means maximum fabricator capacity.

Cnc Beam Drill Line Configuration

Cnc Beam Drill Line Yoke

It may be between a Vertical Machining Centre or a CNC Router when deciding on the CNC machinery that you want to buy. These two pieces of equipment can be used for different purposes. Which one should you choose?

Renishaw Calibration 5 Axis - The calibrator is a Renishaw model APCA45 equipped with a modified spherical stilus. The device includes a retractable lid and an air purge to remove debris and dust during activation. It mounts to the swing arm, which is controlled by the pneumatic rotary.

Tool

Voortman's Raptor 3DCAD/CAM Software is a revolutionary tool that allows users to program CNC faster and more accurately. You can view, modify and export parts information right from the 3D platform. This technology is combined with Voortman CNC technology gives fabricators maximum productivity.

Gulf States Saw & Machine Co has the fastest automated Drill Lines. We have a range of Drill Lines as well as Beam Drill Lines to meet your needs for quality labor and low costs.

Cnc Beam Drill Line Configuration

Check our other pages :

Cnc Beam Drill Line Type

This Morse Taper Chuck adaptor allows for standard parallel shank drill bits to be used when drilling smaller diameters. It permits a maximum drill size of? It permits a maximum diameter of 12mm (12mm) as well as a minimum diameter 3/64’’ (1mm).

"..We have drilled around 25,000 holes since purchasing our CNC Beam Drill Line approximately four months ago. It used to take 5 minutes to drill each hole. We now spend approximately. 30 seconds per hole, which is a saving of 1875 man-hours over the course of 4 months. That's $84,375 for our shop! You can see that this machine will pay back in less than one years. This machine not only speeds up our production, but it also opens up the floor for new jobs.

Frequently Asked Questions

Theoretically, a beam could be any length provided it was properly designed. The issue is one of practicality. Although it's theoretically possible to have an RC beam 16m long, it is very difficult to have a reinforcement bars that are longer than 12m.

ECC works with a finite field. This means that even though elliptical curvatures are relatively new, the majority of the math required to calculate a discrete logarithm across the field is older. Most of the algorithms used in ECC are minor variations of factoring algorithms.

Channels, or C-beams, are used when the flat back side of the web is mounted to another flat surface. This allows for maximum contact. Sometimes they are welded back-to-back to create a non-standard I beam.

The dimensions of the steel bars required for beam and column are determined by the design structure, load on it, and span between two supports. For beam and column, the size of steel bars is generally 12mm to 25mm.

The shorter beam will therefore be stronger for the same load. To compare beam strengths as the length changes, it takes more than the section modulus.